THM Carbones bearing cups for Clavicula

Montrer tous les produits THM Carbones
  • THM Carbones bearing cups for Clavicula

    BSA Bearings MTB
    BSA aluminium bearings compatible with Clavicula M3 MTB
    • Color: Black
    • SKU: 20100003


    BSA Bearings ROAD
    BSA aluminium bearings compatible with Clavicula SE and Clavicula M3 Road.
    • Color: Black
    • SKU: 20100001


    Pressfit 30 Bearings MTB
    The Pressfit 30 is suitable for frame with the width that is either 68 mm or 73 mm and with the inner diameter of 46 mm. We supply a system adaption with cups installed from outside, offering the bearings a contact width of 93 mm (MTB).
    • Color: Silver
    • SKU: 20100014


    Pressfit 30 Bearings ROAD
    The Pressfit 30 is suitable for frame with the width that is either 68 mm or 73 mm and with the inner diameter of 46 mm. We supply a system adaption with cups installed from outside, offering the bearings a contact width of 85.5 mm (Road).
    • Color: Black
    • SKU: 20100013


    Shimano Press Fit Bearings MTB
    This is a meantime frequently used bottom bracket mounting facility composed of Ø 41 mm cups to be pressed in. There are two MTB versions, one for 92 mm frame width (symmetrical to the center line) and another for 89.5 mm frame width (unsymmetrical).
    • Color: Silver
    • SKU: 20100012


    Shimano Press Fit Bearings ROAD
    This is a meantime frequently used bottom bracket mounting facility composed of Ø 41 mm cups to be pressed in. The “Road” variant is for 86.5 mm frame width.
    • Color: Silver
    • SKU: 20100011


    BB30 Bearings MTB
    These bearing cups are suited for installation of the THM Clavicula on frames with bottom bracket housings to BB30 standard applicable to axles with 30 mm diameter. The bottom bracket housing is 68 mm wide and its inner diameter is 42 mm. The snap rings wich for the BB30 standard are used as limit stop when pressing in the bearings, must not be installed. The relatively small bearing clearance of 68 mm could lead to considerable axle deformations. Our solution with bearings at the outside involves a reduced load on the axle which can be seen from the higher rigidity. Another advantage is the facility of using the same crank for frames to BB30 standard and those with BSA or Italian thread. The increase in weight of the complete system is neglegible.
    • Color: Silver
    • SKU: 20100009


    BB30 Bearings ROAD
    These bearing cups are suited for installation of the THM Clavicula on frames with bottom bracket housings to BB30 standard applicable to axles with 30 mm diameter. The bottom bracket housing is 68 mm wide and its inner diameter is 42 mm. The snap rings wich for the BB30 standard are used as limit stop when pressing in the bearings, must not be installed. The relatively small bearing clearance of 68 mm could lead to considerable axle deformations. Our solution with bearings at the outside involves a reduced load on the axle which can be seen from the higher rigidity. Another advantage is the facility of using the same crank for frames to BB30 standard and those with BSA or Italian thread. The increase in weight of the complete system is neglegible.
    • Color: Black
    • SKU: 20100008


    BBRIGHT Press Fit Bearings MTB
    BBright is the only bottom bracket standard that allows an oversized bottom bracket axle (30mm diameter) and oversized chainstay, seat and down tubes (11mm wider). The BBright Press Fit has an inside diameter of nominally 46mm. Compatible with the MTB version of the Clavicula.
    • Color: Silver
    • SKU: 20100020


    BBRIGHT Press Fit Bearings ROAD
    BBright is the only bottom bracket standard that allows an oversized bottom bracket axle (30mm diameter) and oversized chainstay, seat and down tubes (11mm wider). The BBright Press Fit has an inside diameter of nominally 46mm. Compatible with the Road versions of the Clavicula.
    • Color: Silver
    • SKU: 20100016


    BBRIGHT Direct Fit Bearings
    BBright is the only bottom bracket standard that allows an oversized bottom bracket axle (30mm diameter) and oversized chainstay, seat and down tubes (11mm wider). BBright Direct Fit has a shell inside diameter of nominally 42mm.
    • Color: Silver
    • SKU: 20100015


    Bearing Shells ITA
    Bearing shells with Italian thread sold with bearings, compatible with Clavicula SE and Clavicula M3 Road.
    • Color: Black
    • SKU: 20100002


    BB386 Evo Bearings
    In the 386 EVO the frame shell width is nominally 87mm. The inside diameter is 46mm and the pressed bearings are the same as PF30 bearings, but the crank must have a longer spindle compatible with a 386 EVO bottom bracket frame shell.
    The 386 Evo is compatible with the 3T Exploro frame.
    • Color: Black
    • SKU: 20100019




    THM Carbones Ceramic bearing cups for Clavicula

    BSA Hybrid Ceramic Bearings ROAD
    BSA aluminium Hybrid Ceramic bearings. We use high-grade steel rings with ceramic balls which are treated according to a special greasing and sealing procedure. The main benefit is less an extreme smoothness in operation than a longer service life and reduced maintenance. Due to the special properties of steel and ceramics this combination is however not suited to withstand severe shockloads, so we offer these bearings for our road version only.
    • Color: Black
    • SKU: 20100004


    BB30 Hybrid Ceramic Bearings ROAD
    These bearing cups are suited for installation of the THM Clavicula on frames with bottom bracket housings to BB30 standard applicable to axles with 30 mm diameter. The bottom bracket housing is 68 mm wide and its inner diameter is 42 mm. The snap rings wich for the BB30 standard are used as limit stop when pressing in the bearings, must not be installed. The relatively small bearing clearance of 68 mm could lead to considerable axle deformations. Our solution with bearings at the outside involves a reduced load on the axle which can be seen from the higher rigidity. Another advantage is the facility of using the same crank for frames to BB30 standard and those with BSA or Italian thread. The increase in weight of the complete system is neglegible.
    • Color: Black
    • SKU: 20100010


    ITA Hybrid Ceramic Bearings
    Italian aluminium Hybrid Ceramic bearings. We use high-grade steel rings with ceramic balls which are treated according to a special greasing and sealing procedure. The main benefit is less an extreme smoothness in operation than a longer service life and reduced maintenance. Due to the special properties of steel and ceramics this combination is however not suited to withstand severe shockloads, so we offer these bearings for our road version only.
    • Color: Black
    • SKU: 20100005
  • Rate this product

    •  
    • Unfortunately, there isn't any review yet. Be the first one and share your experiences with thousands of other riders!
  • THM Carbones a été récompensé par le sceau de la qualité allemande décerné par l'organisation fédérale de la recherche.

    Depuis 20 ans la société THM explore les meilleures approches possibles afin de développer des composants de hautes performances et qui font référence dans l'art du carbone.

    L'orientation précise des fibres de carbone selon les efforts dans la pièce permettent une utilisation optimale du potentiel du matériau. De ce fait THM carbone s'est inspiré par la structure naturelle des os pour atteindre la performance maximale combiné avec le minimum de poids du composant.

    Finalement THM a été récompensé par le prix allemand "Innovativ durch Forschung".
  • Les clients qui ont regardé ce produit ont aussi regardé ceci:
Livraison gratuits à partir de 300€
Réponse aux emails en français
Vous êtes ici:
Ce produit est manufacturé à la main en Allemagne